Welcome to Würth Slowakia For trade customers only
Angle connector type B2 For timber structures, short, solid 3 mm design - ANGL-WOCON-B2-40X40X90X3,0 Angle connector type B2 For timber structures, short, solid 3 mm design - ANGL-WOCON-B2-40X40X90X3,0
Angle connector type B2 For timber structures, short, solid 3 mm design - ANGL-WOCON-B2-40X40X90X3,0 - 1
Angle connector type B2 For timber structures, short, solid 3 mm design - ANGL-WOCON-B2-40X40X90X3,0 - 2

Angle connector type B2 For timber structures, short, solid 3 mm design

Angle connector B2
ANGL-WOCON-B2-40X40X90X3,0

Art.-no. 068103590
EAN 4024835118088
All versions

Price for selected packaging unit
Angle connector type B2 For timber structures, short, solid 3 mm design

Art.-no. 068103590

Price for selected packaging unit
Quantity
PU
x 50 pcs

Exclusively for trade customers

Register now and access more than 125,000 products

For high-quality connections in load-bearing wood/wood or wood/concrete structures. It is advisable to use rib-reinforced angle connectors for more demanding requirements.
  • Minimal misalignment between wooden structure and concrete anchor

  • Low bulk, slim design

  • Sheet metal hot-dip galvanised on both sides (DX51D + Z275 [approx. 20 µm]) in line with EN 10327:2004

  • Application in utilisation classes 1 and 2 in line with EN 1995:2013
Proof of Performance

ETA-09/216

Notice

The diameter of bolts/screws/anchors may only be max. 2 mm smaller than the diameter of the hole. The respective basic conditions of the applicable anchor approval must be observed.

Product information

Würth Catalogue

Datasheets(X)

Certificates/ Documents

 | 

 | 

Application area

Load-bearing connections of timber joists to wood or concrete such as joist to joist, purlin to joist, joist to concrete substrate.

Instructions

Suitable fasteners:


  • Comb/ribbed nail in line with EN 14592: 4.0 x 40 mm

  • ASSY 3.0 combination screw in line with ETA 11/0190: d = 12 mm

  • Bolts according to manufacturer specification: d = 12 mm

  • Recommended dowels for anchoring in concrete: W-BS; W-FAZ; W-VIZ; WIT-VM 250; WIT-UH 300

Type

B2

Width x height x depth

40 x 90 x 42 mm

Thickness

3 mm

Design

Without bar

Number of D 13 mm holes in subcarrier nJ/main carrier nH

2 + 1 PCS

Number of D 5 mm holes in subcarrier nJ + main carrier nH

8 + 4 PCS

Approval

ETA-09/0216

Product weight (per item)

100.360 g

Material

Steel

Surface

Hot dip galvanized

Weight

98 g

Material designation

DX51D

Material standard

DIN EN 10327:2004

Number of D 5 mm holes

12 PCS

Number of D 13 mm holes

3 PCS

Characteristic load capacity in kN of type B1/B2 angle bracket according to ETA-09/0216 with ring-shank nail - purlin/post
Angle bracket B1/B2Article numberETARing-shank nail in Angle bracket B1/B2 for each connection
F1,RkF2/3,RkF4,RkF5,Rk
Width x length x depth x
thickness in mm 		SteelWoodWoodSteelWoodSteel
mmkNkNkNkNkNkNkN
1 angle B40x90x42x3 mm0681 035 9009/02164x400,921,372,56----
40x160x42x3 mm0681 050 16009/02164x400,921,372,73----
2 angle B40x90x42x3 mm0681 035 9009/02164x401,852,755,125,134,285,134,28
40x160x42x3 mm0681 050 16009/02164x401,852,755,466,484,796,484,79
3) If one angle bracket is used for each connection, the connected component must be secured against twisting.
4) The loads F4 and F5 act on the top edge of the connected component. Securing against twisting is not required.
The specified load-bearing capacities apply to coniferous wood at 350 kg/m³ ≤ rk ≤ 420 kg/m³.
For wood at 290 kg/m³ ≤rk≤ 350 kg/m³, the specified load-bearing capacities for wood must be multiplied by the factor kdens:

tSteel ≥ 2.5 mm: kdens = (pk/350)^2

tSteel = 1.5 mm: kdens = (pk/350)^0.8

Rated values of the load-bearing capacities: Fi,Rd = min {Fi,wood,Rd; Fi,steel,Rd}
failure of the fastener in the wood: Fi,Wood,Rd = kmod / ƳM,Wood × Fi,Wood,Rk with ƳM,Wood = 1.3
Steel failure of the connector: Fi,Steel,Rd = Fi,Steel,Rk / ƳM,Steel with ƳM,Steel = 1.25
For several simultaneous loads, the following condition must be met:

The specified nailing patterns must be observed in accordance with the relevant ETA.
NOTE: These are guides for planning purposes. The values must be calculated for each project by authorised persons.
Characteristic load capacity in kN of type B1/B2 angle bracket according to ETA-09/0216 with ring-shank nail - purlin/post
Steel or reinforced concrete connection with a stud/stud anchor
Angle bracket B1/B2eBz(1+eB/z)
40x90x42x3 mm24,517,52,4
40x160x42x3 mm24,517,52,4
FB,Ed = F1,d x (1+ eB/z)

If the load F4 or F5 acts with a higher eccentricity "e" than the top edge of the angle, an additional ΔF1 load must be applied to both angles. This is applied at the angles by an additional momentum and a pair of forces. B is the distance between the angles (width of the component to be connected).

ΔF1,d = F4,d / F5,d x e/B
Required accessory:
 
Product
Description
Quantity
PU
Price
/PU
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)

ANC-(W-VIZ-A/S)-(A2K)-10-M10X85

x 10 pcs
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)

ANC-(W-VIZ-A/S)-(A2K)-20-M10X95

x 10 pcs
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)

ANC-(W-VIZ-A/S)-(A2K)-30-M10X105

x 10 pcs
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)

ANC-(W-VIZ-A/S)-(A2K)-60-M10X135

x 10 pcs
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)
W-VIZ-A anchor rod, zinc-plated steel for W-VIZ/S injection systems (concrete)

ANC-(W-VIZ-A/S)-(A2K)-100-M10X175

x 10 pcs
The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.
The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076
Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units
The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.
In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).

Art.-no.
Cust. Mat. No.

Hazardous Material

Product information

Würth Catalogue

Datasheets()

Datasheets ()

CAD data  | 

Certificates/ Documents

 | 

 | 

Technical information
Show all product details