Ceiling nail W-DN - ANC-(W-DN)-(A2K)-4,5-6X40

Ceiling nail W-DN

Name: Ceiling nail W-DN
Brand: Würth
SKU: 09053645

Ceiling nail W-DN
ANC-(W-DN)-(A2K)-4,5-6X40

Art.-no. 09053645

EAN 4011231850407

All versions

Similar products

Price for selected packaging unit

Ceiling nail W-DN

Art.-no. 09053645

Price for selected packaging unit

Quantity

x 200 pcs

Exclusively for trade customers

Login/Register
Call customer service: 0800 121 854

Easy mounting: Plug it in, drive it flush, and done! For the mounting of ceiling suspensions or C-profiles in dry walling. For concrete, zinc-plated steel

Push-through installation

Small drill hole depth

Small drill hole diameter

Immediate load-bearing capacity — no waiting

Easy insertion: Knock in protruding pin with hammer until flush

No special drills or setting tools required

Anchorage via friction locking — distance-controlled expanding anchor

Proof of Performance

Anchors in a non-structural system based on a redundant design in concrete: European Technical Approval ETA-12/0029

Dimensioned in accordance with the European Technical Approval Guidelines (ETAG) for "Metal Anchors for Use in Concrete", Appendix C, design method C

Anchorage with European Technical Approval in cracked concrete (concrete tensile zone) and non-cracked concrete (concrete compression zone)

The anchor has European Technical Approval for use in reinforced or unreinforced normal weight concrete with a strength class of min. C20/25 and max. C50/60 in accordance with EN 206-1:2000-12

Fire resistance: R30, R60, R90, R120 (base material: concrete C20/25 to C50/60): Technical Report TR 020 "Evaluation of anchorages in concrete concerning resistance to fire" (included in ETA-12/0029)

Notice

Anchors in a non-structural system based on a redundant design in concrete (for all load directions)

The partial safety factors of the resistances regulated in the approval and a partial safety factor of the effects of Y_F = 1.4 have been taken into account. Please refer to the European Technical Approval Guidelines (ETAG), Appendix C, for information on combining tensile and transverse loads, influence of the edge distance and groups of anchors.

Permissible load when exposed to fire

The partial safety factors for load-bearing capacity on exposure to fire of Y_M,fi= 1.0 as recommended in the approval and the partial safety factor of the effects of Y_F = 1.0 have been taken into account.

Nominal drill diameter and diameter of cutting edges of the drill

Tungsten carbide hammer drill bits must comply with the specifications set out in the information leaflet of the Deutsches Institut für Bautechnik (German Institute of Civil Engineering - DIBt) and the Association of German Tool Manufacturers (FWI) on the "characteristic values, requirements and tests for masonry drill bits with tungsten carbide cutting body which are used for the manufacture of drilled holes for anchoring". Würth hammer drill bits meet the specifications set out in the information leaflet.

Application area

Suspended ceilings

Create the drill hole

Clean the drill hole

Insert anchor through component

Knock in pin until flush

Product information

Würth Catalogue

Datasheets(X)

CAD data (available after login)

Certificates/ Documents

Application area

Suitable for attaching lightweight ceiling cladding and suspended ceilings, metal profiles, perforated strips, wire hangers, vernier hangers, wooden strips, wooden laths, square timbers, etc.

May only be used in dry indoor room conditions

Type description	W-DN
Material	Steel
Surface	Zinc plated
Anchor diameter	6 mm
Length	40 mm
Max. attachment height (t fix)	5 mm
Effective anchoring depth (h ef)	32 mm
Nominal drill-bit diameter (d 0)	6 mm
Drill hole depth (h 0)	40 mm
Through-hole in the component to be connected (d f)	7 mm

¹⁾The partial safety factors of the resistances regulated in the approval and a partial safety factor of the effects of γF = 1.4 have been taken into account. Please refer to the European Technical Approval Guidelines (ETAG), Annex C, for information on combining tensile and shear loads, influence of the edge distance and groups of anchors. ²⁾ The partial safety factors for load capacity under exposure to fire of γ_M,fi = 1.0 and the partial safety factor of the actions of γ_F = 1.0 have been taken into account. ³⁾ Tungsten carbide hammer drill bits must comply with the specifications set out in the information leaflet of the Deutsches Institut für Bautechnik (German Institute of Civil Engineering - DIBt) and the Fachverband Werkzeugindustrie e.V. (Association of German Tool Manufacturers - FWI) on the characteristic values, requirements and tests for masonry drill bits with tungsten carbide cutting body which are used for the manufacture of drilled holes for anchoring. Würth hammer drill bits meet the specifications set out in the information leaflet. ⁴⁾ Number of attachment points ≥ 3 and at least one anchor per attachment point produces a load per attachment point of F_zul ≤ 1.4 kN or number of attachment points ≥ 4 and at least one anchor per attachment point produces a load per attachment point of F_zul ≤ 2.1 kN. The admissible loads can be increased if the design shows that the requirements governing the strength and rigidity of the component to be attached remain satisfied even after the failure of an anchor in terms of the limit state of serviceability and load-bearing capacity.

Characteristic values
Axis spacing	s_cr [mm]	200
Edge distance	c_cr [mm]	150
Minimum member thickness	h_min [mm]	80
Effective anchorage depth	h_ef [mm]	32
Nominal drill ∅ ³⁾	d₀ [mm]	6
Cutting edge ∅ ³⁾	d_cut ≤ [mm]	6,4
Drill hole depth	h₀ ≥ [mm]	40
Through hole in the component being connected	d_f≤ [mm]	7
³⁾ Tungsten carbide hammer drill bits must comply with the specifications set out in the information leaflet of the Deutsches Institut für Bautechnik (German Institute of Civil Engineering - DIBt) and the Fachverband Werkzeugindustrie e.V. (Association of German Tool Manufacturers - FWI) on the characteristic values, requirements and tests for masonry drill bits with tungsten carbide cutting body which are used for the manufacture of drilled holes for anchoring. Würth hammer drill bits meet the specifications set out in the information leaflet.

Additional accessory:

Product

Description

Quantity

Price
/PU

Blow-out bulb for drill hole cleaning

BLWOUTBULB-F.CLN

Art.-no. 0903990003

For cleaning drill holes with a smaller diameter

The packaging unit defines the number of articles in one packaging. In the catalog segment you can choose from different packaging units if a pop-up menu is displayed.

Just leave the field empty if you don't know the packaging unit when directly entering the article number in the shopping basket or when importing with Easy-/VarioScan. The packaging unit will be determined automatically.

The article number is made up of the following: VVVVAAABBB
VVVV = 4 digits for prefix number (please note that the first digit is currently always 0)
AAA = 3 digits for dimension part 1
BBB = 3 digits for dimension part 2

Example article number structures:
Example 1: Screw with dimensions of 4x10 mm:
VVVVAAABBB
00574 10 (2 spaces between the 4 and the 10)

Example 2: Screw with dimensions of 10x20 mm:
VVVVAAABBB
005710 20 (1 space between the 10 and the 20)

Example 3: Flat washer with an internal diameter of 6 mm:
VVVVAAABBB
04076

Price per packaging unit (PU):
The displayed price is always in line with the displayed packaging, if the PU is 250 the price for 250 units, if the PU is 300 the price for 300 units.

Price with price key representation (PSL):
The price always applies to a quantity ruled through the price key:
Price for 1 unit
Price for 100 units
Price for 1000 units

The quantity shows the number of pieces or units of measure contained in the order or delivery for the respective article.

In contrast to sales packaging and secondary packaging, the disposal costs for chemical-technical products are shown separately. The breakdown of the individual costs can be found on the relevant products and also in the shopping cart, as well as in our General Terms and Conditions (GTC).