EURASEAL U-305 universal window sealing tape for indoor and outdoor use
WNDWSEALTPE-(U-305)-EASY-FSA-W200MM-L20M
Art.-no. 0875594200
EAN 4061975344878
Register now and access more than 125,000 products
Very high performance
- The membrane's variable Sd value ensures particularly effective drying of the joint
- Reduces the risk of building damage caused by moisture and mould in the structure
- Increases the performance of the insulating material
Versatile
- Can be used for sealing both indoors and outdoors
- Double-sided adhesive means the tape can be bonded on the same or opposite side
- Free zone without adhesive improves diffusion behaviour and compensates for component movements
Straightforward to use
- Quality-controlled installation in accordance with the requirements of the German RAL quality assurance association for windows and doors
- Special acrylate adhesive with very high adhesive strength for full-surface self adhesion
- Easy to plaster over
- High-quality, flexible fleece is very pleasant to work with
This product is classified in accordance with EMICODE® (EC1 Plus). EMICODE® is an independent labelling system for low-emission products, based on specified test methods and limit values.
- On mineral and highly absorbent surfaces, use adhesion primer spray or butyl/bitumen primer.
- Combine as follows: Window sealing tape inside and VKP Plus outside.
- Combine as follows: Perfect neutral silicone inside and window sealing tape outside.
- Combine as follows: Indoor and outdoor window sealing tape.
- Form the outer seal of the lower connection in the shape of a tray (sloping outwards).
Datasheets(X)
- For sealing window and door joints in new buildings and redevelopment projects.
- Suitable for smooth masonry reveals.
- The surfaces must be dry and free from dust and grease, promote adhesion and be capable of bearing loads.
- Pre-treat mineral and highly absorbent surfaces with WÜRTH spray primer or butyl primer.
- The reveal must have a smooth coating in accordance with DIN 4108-7 in order for Euraseal U-305 universal window sealing tape to be applied.
- Good adhesion is usually possible on concrete, calcium silicate block, wooden surfaces, OSB boards, gypsum plasterboards, gypsum fibreboards, hard PVC and metal surfaces.
- Unroll the sealing tape and cut it to size, including approx. 5 cm of additional length (measured from the element to be glued).
- Installation on windows: Remove the protective film from the self-adhesive strip and press the window sealing tape firmly onto the blind frame using a press-on roller. For adhesion to the outside, follow the same process as for the inside.
- Follow the same process for all areas to be sealed.
- Align and secure the element, then use PURLOGIC PU foam to completely fill the space between the element and the building structure.
- Installation on masonry: Remove the protective film either completely or partially as required from the fully bonded side. Secure to the wall and press on firmly using a press-on roller.
- Corners are formed by creating loops or overlaps. Make sure that the strips of tape are fully sealed in the corner and overlap areas.
- The fleece-laminated side can be plastered with commercially available plaster mortars. The fleece-laminated side remains visible (trowel logo).
- Form the outer seal of the lower connection in the shape of a tray (sloping outwards).
- Pass the side seal over the bottom seal.
- Small defects can be closed up using Plus flexible tape adhesive.
- When plastering the window sealing tape, observe the regulations of the current "Verputzen von Fensteranschlussfolien" (Plastering of Window Connection Films) plasterer's guidelines.
- For doors and floor-level elements, observe the regulations of DIN 18533.
- To protect the functional membrane, the film should be secured on both sides as soon as possible after installation (max. 24 hours).
- When used at 0 to -5 °C, the initial adhesive strength is reduced. It is still possible to install the product at these temperatures, but a longer contact time is required in order to achieve a high final strength.
 | |
Colour | White |
Backing material | PET fleece |
Width | 200 mm |
Thickness | 0.4 mm |
Length of roll | 20 m |
Min./max. processing temperature | -5 to 30 °C |
Min./max. temperature resistance | -30 to 100 °C |
Min. resistance against driving rain (pressure)/conditions | 1200 Pa / in accordance with DIN EN 1027 |
Building material class/conditions | E - Normally inflammable / in accordance with DIN EN 13501-1 |
Ultraviolet resistance | 12 months |
Max. outdoor exposure | 3 Month |
Shelf life from production/conditions | 12 Month / at 15°C to 20°C |
| Water vapour diffusion-equivalent air layer thickness | |
| Humidity 0–17%: | > 5.5 m |
| Humidity 17–50%: | > 2.6 m |
| Humidity > 90% | < 1 m |
Select RAL-colour code
!! NOTE: On-screen visualisation of the colour differs from real colour shade!!
Last viewed
Hexagon bolt with thread up to the head DIN 933, steel 10.9, zinc-plated, blue passivated (A2K)
Hexagon bolt with shank ISO 4014, A4-50 and A4-70 stainless steel, plain
Hexagon bolt with thread up to the head ISO 4017, A2-80 stainless steel, plain
Hexagon nut DIN 934, I10I steel with silver zinc-flake coating (ZFSHL)
WÜPOFAST® zinc-plated yellow chipboard screw steel, zinc-plated yellow, full thread, countersunk head, PZ
HPC solid carbide drill Speeddrill 4.0-Inox, DIN 6537L, long 5xD, 4 drill heels, with internal cooling
Countersunk screw, type SK/S — push-through installation DIN 7991 (ISO 10462) steel grade 8.8, zinc plated blue, with countersunk washer, steel, zinc plated blue
Pan Head screw with hexalobular head ISO 14583, steel, strength class 8.8, zinc-nickel-plated, black (ZNBHL)
Hexagonal bolt with shank ISO 4014, plain A2-50 and A2-70 stainless steel
Insider S1 FLEXITEC® ESD safety shoe